Thank you in advance for any help
I have a Galaga arcade cabinet with a WG k4600 and kinda have things working.
My setup:
Mister with analog board -> Jpac with no jumpers set (direct passthrough) -> Jamma to Galaga converter.
Good: I've been able to get this setup working, sort of... Games like Galaga, Arkanoid, and Donley Kong work great.
Not Good: If I try to launch games like Zaxon or DoDonPachi (and many others) the monitor doesn't sync.
Any Mister config recommendations (ini at end of post)
other info:
- Not sure if it is relevant or not, but the monitor doesn't sync right on boot until the mister menu pops up.
- I'm not super experienced with adjusting arcade monitors. I messed around with the Horizontal size as well as the Vertical Size and V Hold (V and H are what is printed on the adjustment, it is mounted tate)
- I ran the 240p test suite in the SNES core and everything looks decent.
Code: Select all
key_menu_as_rgui=0 ; set to 1 to make the MENU key map to RGUI in Minimig (e.g. for Right Amiga)
forced_scandoubler=0 ; set to 1 to run scandoubler on VGA output always (depends on core).
ypbpr=0 ; set to 1 for YPbPr on VGA output.
composite_sync=1 ; set to 1 for composite sync on HSync signal of VGA output.
vga_scaler=0 ; set to 1 to connect VGA to scaler output.
hdmi_audio_96k=0 ; set to 1 for 96khz/16bit HDMI audio (48khz/16bit otherwise)
keyrah_mode=0x18d80002 ; VIDPID of keyrah for special code translation (0x23418037 for Arduino Micro)
vscale_mode=0 ; 0 - scale to fit the screen height.
; 1 - use integer scale only.
; 2 - use 0.5 steps of scale.
; 3 - use 0.25 steps of scale.
; 4 - integer resolution scaling, use core aspect ratio
; 5 - integer resolution scaling, maintain display aspect ratio
vscale_border=0 ; set vertical border for TVs cutting the upper/bottom parts of screen (1-399)
;bootscreen=0 ; uncomment to disable boot screen of some cores like Minimig.
;mouse_throttle=10 ; 1-100 mouse speed divider. Useful for very sensitive mice
rbf_hide_datecode=0 ; 1 - hides datecodes from rbf file names. Press F2 for quick temporary toggle
menu_pal=0 ; 1 - PAL mode for menu core
hdmi_limited=0 ; 1 - use limited (16..235) color range over HDMI
; 2 - use limited (16..255) color range over HDMI, for VGA converters.
direct_video=0 ; 1 - enable core video timing over HDMI, use only with VGA converters.
hdr=0 ; 1 - enable HDR using the BT2020 color space (faux-HDR, use color controls to tweak).
; 2 - enable HDR using the DCI P3 color space.
; 3 - enable HDR without color space conversion.
fb_size=0 ; 0 - automatic, 1 - full size, 2 - 1/2 of resolution, 4 - 1/4 of resolution.
fb_terminal=1 ; 1 - enabled (default), 0 - disabled
osd_timeout=30 ; 5-3600 timeout (in seconds) for OSD to disappear in Menu core. 0 - never timeout.
; Background picture will get darker after double timeout
video_off=0 ; output black frame in Menu core after timeout (is seconds). Valid only if osd_timout is non zero.
osd_rotate=1 ; Display OSD menu rotated, 0 - no rotation, 1 - rotate right (+90°), 2 - rotate left (-90°)
vga_sog=0 ; 1 - enable sync on green (needs analog I/O board v6.0 or newer).
Code: Select all
; calculated mode: width,height,refresh[,flags]
; example: video_mode=1920,1200,60
; flags - cvt=CVT timing, cvtrb=CVT-RB timing (default)
; video_mode=0